CAO course · Level 8 · Round 1 2026

AU681 Furniture Design and Manufacture, ATU: CAO points 2026

Atlantic Technological University, Level 8. Round 1 2026 points: 400. Round 2: 380. Down 9 on 2025, when Round 1 was 409 and the final cut-off 404. Points last checked 8 September 2026.

CAO lists this course as “Furniture Design and Manufacture [Letterfrack]”. "Letterfrack" is the campus or stream the course runs on.

Round 1 points
400
2025 Round 1
409
Level
8
College
ATU

AU681 points history, 2023 to 2026

Round 1 is the main cut-off. The last column is the final figure after all rounds for past years, and the most recent round so far for 2026.

From 2023 to 2025 the Round 1 cut-off ranged from 400 (2023) to 409 (2025), an average of 403. 2026, at 400, is close to that average.

4002023400202440920254002026
Round 1 cut-off by year; the scale starts at 370 points. Gaps are years with no points figure.
YearRound 1Final
2026400380
2025409404
2024400400
2023400400

2026 figures from the CAO points lists, checked 8 September 2026. Earlier years from the official CAO points charts for 2021 to 2025. Years when CAO used this code for a different course are left out.

How far are you from 400?

Put your grades into the calculator. It applies the best-six rule, the Higher Maths bonus and LCVP the way CAO does, then compare your total with 400.

cut-off 400
0100200300400500625

What 400 looks like in grades

  • 1 × H3 and 5 × H4 at Higher Level = 407 points
  • or 4 × H4 and 2 × H5 with Higher Maths (H6 or better adds 25) = 401

Only your best six subjects count. Meeting the points is not enough on its own: the course’s minimum entry requirements (specific subjects and grades) apply too.

Work out your points and compare

400 points is above roughly 52% of 2026 candidates (about 48.1% scored 400 or more). See the full 2026 points distribution.

Similar courses

Courses in the same subject area or at the same college, within 30 points of 400.

Other courses at ATU

The ATU courses closest in points to AU681. All ATU courses and points.

Round 2

Round 2 cut-off: 380 points, down 20 from Round 1.

The main figure on this page is the Round 1 cut-off: the points of the last applicant offered a place. It is not a fixed entry requirement. When Round 1 offers are turned down, places free up and points can fall in Round 2. See the CAO key dates and how CAO offers work.

Questions about AU681

What were the CAO points for AU681 in 2026?

Furniture Design and Manufacture (AU681) at Atlantic Technological University had a Round 1 cut-off of 400 points in 2026. The Round 2 cut-off was 380.

What were the points for AU681 in 2025?

The 2025 Round 1 cut-off for AU681 was 409 points, Round 2 was 404 and the final end-of-season figure was 404. Down 9 on 2025, when Round 1 was 409 and the final cut-off 404.

Is AU681 a Level 8 course?

Yes. AU681 appears on the CAO Level 8 list, so it is an honours bachelor degree.

Did points for AU681 drop in Round 2?

Round 2 cut-off: 380 points, down 20 from Round 1. Round 2 offers went out on Monday 7 September 2026. Later rounds only matter for courses that still have places.

Search all 1,376 CAO courses or go back to the points calculator.