CAO course · Level 7 · Round 1 2026

AU583 Furniture Design, Making and Technology - Common Entry, ATU: CAO points 2026

Atlantic Technological University, Level 7. Round 1 2026 points: 337. Down 14 on 2025, when Round 1 was 351. Points last checked 8 September 2026.

CAO lists this course as “Furniture Design, Making and Technology - Common Entry [Letterfrack]”. "Letterfrack" is the campus or stream the course runs on.

Round 1 points
337
2025 Round 1
351
Level
7
College
ATU

AU583 points history, 2023 to 2026

Round 1 is the main cut-off. The last column is the final figure after all rounds for past years, and the most recent round so far for 2026.

From 2023 to 2025 the Round 1 cut-off ranged from 320 (2024) to 351 (2025), an average of 336. 2026, at 337, is close to that average.

3362023320202435120253372026
Round 1 cut-off by year; the scale starts at 290 points. Gaps are years with no points figure.
YearRound 1Final
2026337337
2025351351
2024320320
2023336351

2026 figures from the CAO points lists, checked 8 September 2026. Earlier years from the official CAO points charts for 2021 to 2025. Years when CAO used this code for a different course are left out.

How far are you from 337?

Put your grades into the calculator. It applies the best-six rule, the Higher Maths bonus and LCVP the way CAO does, then compare your total with 337.

cut-off 337
0100200300400500625

What 337 looks like in grades

  • 1 × H4 and 5 × H5 at Higher Level = 346 points
  • or 4 × H5 and 2 × H6 with Higher Maths (H6 or better adds 25) = 341

Only your best six subjects count. Meeting the points is not enough on its own: the course’s minimum entry requirements (specific subjects and grades) apply too.

Work out your points and compare

337 points is above roughly 33% of 2026 candidates (about 66.6% scored 330 or more). See the full 2026 points distribution.

Similar courses

Courses in the same subject area or at the same college, within 30 points of 337.

Other courses at ATU

The ATU courses closest in points to AU583. All ATU courses and points.

Round 2

No Round 2 offers were made for AU583: the Round 1 cut-off was the last one.

The main figure on this page is the Round 1 cut-off: the points of the last applicant offered a place. It is not a fixed entry requirement. When Round 1 offers are turned down, places free up and points can fall in Round 2. See the CAO key dates and how CAO offers work.

Questions about AU583

What were the CAO points for AU583 in 2026?

Furniture Design, Making and Technology - Common Entry (AU583) at Atlantic Technological University had a Round 1 cut-off of 337 points in 2026.

What were the points for AU583 in 2025?

The 2025 Round 1 cut-off for AU583 was 351 points. Down 14 on 2025, when Round 1 was 351.

Is AU583 a Level 8 course?

No. AU583 appears on the CAO Level 7/6 list, so it is an ordinary bachelor degree or a higher certificate, not a Level 8 honours degree. Many Level 7 courses offer a route on to Level 8 afterwards.

Did points for AU583 drop in Round 2?

No Round 2 offers were made for AU583: the Round 1 cut-off was the last one. Round 2 offers went out on Monday 7 September 2026. Later rounds only matter for courses that still have places.

Search all 1,376 CAO courses or go back to the points calculator.